The SmartMyTracks is a application for "SONY SmartWatch" with Google My Tracks works on your terminal. This application can control to start & pause & stop record tracks and mark waypoints of Google My Tracks on your terminal via SmartWatch.
[NOTE]
To use SmartMyTracks you need to check "Menu>More>Settings>Sharing>Allow access" in My Tracks's menu on your terminal.
Also don't use storage setting to "Move to SD card" for My Tracks.
[Operation]
Shown a track recording ready display, after the SmartMyTrack launched. Recording starts by "Round-shaped button" with long-push operation. Already a recording has started; it changes to following display automatically.
During a recording, you can select the display feature SPEED or PACE or TOTAL DISTANCE or ALTITUDE by swipe right(km/h,/km,KM,ALT m) / left(MPH,/mile,Mile,ALT ft). Recording stops by "Square-sheped button" with long-push operation. Marker set by "Pin button" with tapping.
Additionally you can change the screen power-save setting by "left-top mark" tapping. Note that if you set the power-save off, the SmartWatch battery exhaust early. Also if My Tracks access setting is disabled, it shown not allowed display after recording starts.
1. Track recording ready display.
Start a tracking : Long-push a "Round-shaped button".
Screen power save : Tap a "left-top mark".
2. Track recording display
Pause a tracking : Tap a "Pause button".
Stop a tracking : Long-push a "Pause button".
Mark a waypoint : Tap a "Pin button"
Screen power save : Tap a "left-top mark".
3. Track pausing display
Resume a tracking : Tap a "Pause button".
Stop a tracking : Long-push a "Pause button".
Screen power save : Tap a "left-top mark".
[Life cycle]
The track recording is still continuing after the SmartMyTracks exit. Also the recording is continuing after the SmartMyTracks re-start and you can control them. So you can use other application once the SmartMyTracks exit.
If you have any question, please contact below address.
aznable.maro@gmail.com
[Tested terminal with "SONY SmartWatch"]
Sony Ericsson Xperia ray SO-03C
Smart Connect extension for SmartWatch 2
LiveWare extension for SmartWatch 2
LiveWare? extension for SmartWatch
LiveWare extension for SmartWatch
SmartMyTracks“索尼SmartWatch的”我的足迹与谷歌在你的终端是一个应用程序。此应用程序可以控制启动与暂停及停止记录轨迹和标记航点的谷歌“我的足迹”在你的终端上通过的SmartWatch。
[注意]
使用的SmartMyTracks你需要检查“选单>更多>设置>共享>允许访问”我的足迹在你的终端的菜单。
也不要使用存储设置“移动到SD卡”我的足迹。
[操作]
磁道记录的准备显示，后推出SmartMyTrack。开始录制“圆形按钮”操作与长推。已经录制已经开始，它改变了自动显示。
在录制过程中，你可以选择显示功能速度或节奏或向右滑动（公里/小时/公里，KM，ALT米），左/总飞行距离或高度（MPH /英里大道，ALT英尺）。由“方sheped的按钮”停止录制操作长推。标记设置攻“针按钮”。
另外，你可以改变屏幕的省电设置“左顶标”的窃听。请注意，如果你设置了电源保存，早期的SmartWatch电池排气。此外，如果“我的足迹”访问设置被禁用，它不允许在录制开始后显示。
1。跟踪记录随时显示。
  启动跟踪：长推“圆形按钮”。
  屏幕省电：点击“左顶标”。
2。追踪记录显示
  暂停跟踪：点击“暂停”按钮“。
  停止跟踪：长推一个“暂停按钮”。
  标记航点：点选“针按钮”
  屏幕省电：点击“左顶标”。
3。轨道暂停显示
  继续跟踪：点击“暂停”按钮“。
  停止跟踪：长推一个“暂停按钮”。
  屏幕省电：点击“左顶标”。
[生命周期]
轨录音仍在继续后SmartMyTracks出口。此外，记录继续的SmartMyTracks重新启动后，你可以控制他们。所以，你可以使用其他应用程序一旦SmartMyTracks出口。
如果您有任何问题，请联系以下地址。
 aznable.maro @ gmail.com
[测试终端用“索尼SmartWatch的”的]
索尼爱立信Xperia射线SO-03C
SmartWatch的智能连接扩展2
SmartWatch的活件扩展2
SmartWatch的活件?扩展
SmartWatch的活件扩展

2013.11.16 ver1.07
-Fixed some display overlap problems for SmartWatch2 SW2.
-Fixed waypoint record's unit is wrong at ALT display.
2013.11.11 ver1.06
-Support My Tracks version 2.0.5
-Fixed button are overlapped in Track recording display.
-Support ALTITUDE display
Swipe right direction SPEED(km/h)→PACE(min'sec"/km)→DISTANCE(km)→ALTITUDE(m)
Swipe left direction SPEED(MPH)→PACE(min'sec"/mile)→DISTANCE(mile)→ALTITUDE(ft)
Checked by My Tracks version 2.0.5